Search found 176 matches
- Fri Dec 05, 2008 5:43 pm
- Forum: 1966 Technical or Mechanical Forum
- Topic: front beam
- Replies: 33
- Views: 47140
bill lets start from the beginning -remove all the grub screws -clean torsion bars -coat bars with clean multi purpose grease -aline so the the countersunk recesses are perfect -slide the set of bars into the beam -aline the center of the bar with the hole for the set screw thats it i think you forg...
- Wed Dec 03, 2008 6:23 pm
- Forum: 1966 Technical or Mechanical Forum
- Topic: front beam
- Replies: 33
- Views: 47140
- Wed Dec 03, 2008 3:26 am
- Forum: 1966 Technical or Mechanical Forum
- Topic: front beam
- Replies: 33
- Views: 47140
bill GO TO MY SITE AND LOOK AT THE BEAM REBUILD LOOK AT ALL THE PICTURES C CLAMP http://volksbugusa.shutterfly.com/ the grub bolts should not be set in untill the one set of arms are installed on one side and then install the grub bolts on that side...you should be able to see the half moon on the s...
- Tue Dec 02, 2008 4:14 am
- Forum: 1966 Technical or Mechanical Forum
- Topic: front beam
- Replies: 33
- Views: 47140
Re: front beam
Matt: what size hex wrench removes the grub screw from the torsion arm?? Got most of the old beam apart. hard time getting the tie rod ends out. what a job!!! Bill 8 mm is the ticket....tie rods are always a pita dont worry about it once you put heat on the rod it will turn... replace with good ger...
- Sun Nov 16, 2008 5:36 am
- Forum: 1966 Technical or Mechanical Forum
- Topic: vert quarter glass
- Replies: 2
- Views: 2121
Re: vert quarter glass
hibomp wrote:i would like any info on installing q glass on a vert . is the pivot atached to the glass frame ? some place i can maybe find a pic. thanks
do you mean , the pin stud bolts with built in washers?
Matt
- Sun Nov 16, 2008 5:33 am
- Forum: 1966 Technical or Mechanical Forum
- Topic: Engine number vs. VIN number
- Replies: 8
- Views: 7036
Re: Engine number vs. VIN number
OK, the '66 has been delivered; pictures coming soon! - First tech question: The VIN is 116 881XXX and the engine number is F0800XXX; in other words, the VIN is about 80k higher than the engine - is there still a chance that it's the original engine, or is the difference in numbers too great? I'm a...
- Tue Oct 28, 2008 5:46 pm
- Forum: Southwest Events
- Topic: Chirco's 13th Annual Bugtoberfest. Oct19 2008, Tucson, AZ
- Replies: 3
- Views: 11281
- Sun Oct 26, 2008 3:23 am
- Forum: 1966 Technical or Mechanical Forum
- Topic: parts
- Replies: 13
- Views: 6286
- Sat Oct 25, 2008 5:41 pm
- Forum: 1966 Technical or Mechanical Forum
- Topic: parts
- Replies: 13
- Views: 6286
- Sat Oct 25, 2008 3:47 pm
- Forum: 1966 Technical or Mechanical Forum
- Topic: parts
- Replies: 13
- Views: 6286
- Fri Oct 24, 2008 2:51 am
- Forum: 1966 Technical or Mechanical Forum
- Topic: parts
- Replies: 13
- Views: 6286
parrot
well any time you need information...look me up....
mdazzo@optonline.net
also go to youtube vw motors you need to understand some basics when it comes to air cooled motors...VALVE ADJUSTMENT the most important maintance...and TIMING. motor can not run hot...is yours a doghouse?
well any time you need information...look me up....
mdazzo@optonline.net
also go to youtube vw motors you need to understand some basics when it comes to air cooled motors...VALVE ADJUSTMENT the most important maintance...and TIMING. motor can not run hot...is yours a doghouse?
- Thu Oct 23, 2008 2:54 pm
- Forum: 1966 Technical or Mechanical Forum
- Topic: parts
- Replies: 13
- Views: 6286
Parrot Nice to meet you. piston set and heads purchase from BROTHERS.If you want good stuff at the very best price...only purchase from these guys..shops like wolfsbug w are very good on everything else but not on engine parts just to much money. have you every set in pistons before? use copper sili...
- Thu Oct 23, 2008 2:34 am
- Forum: 1966 Technical or Mechanical Forum
- Topic: parts
- Replies: 13
- Views: 6286
- Sun Oct 12, 2008 4:27 pm
- Forum: 1966 Technical or Mechanical Forum
- Topic: front beam
- Replies: 33
- Views: 47140
suggested shopping list
Bill here you go Shop with wolfsbug west or bughause I would not use any RED BUSHINGS the make too many sweaks Strip the complete beam take lots of pictures...take note on the steering box angle... -locking tabs for the four main beam bolts you can make out of sheet metal.. -new beam mounting body r...
- Thu Oct 09, 2008 3:05 pm
- Forum: 1966 Technical or Mechanical Forum
- Topic: front beam
- Replies: 33
- Views: 47140
bill no I did not .But if you like I can make a shopping list for you.Are the ball joints good? That will be the most expensive part of the rebuild.Does the ball joints have grease fittings? The reason why I am asking ...if they have fittings time to replace then. The ball joints today are sealed.Th...